Washing Machine Won’t Drain? How to Fix It Safely

A washing machine that will not drain is usually blocked: a kinked or badly placed drain hose, a clogged pump filter (on front loaders), or a blocked drain pipe in the home. Unplug the machine, straighten the hose, clean the pump filter, then run a drain or spin-only cycle.

If you hear the pump hum but no water moves even after cleaning, the pump may have failed and needs service.

By , maker of TalkFixAI · Published

Error code, hose, filter, drain

  1. Step 1: Note any error code, then try a drain or spin cycle

    Write down any code on the display (many machines show a drain code, such as OE on some LG models). Switch the machine off, wait a minute, then select Drain, Spin or Rinse + Spin. Very heavy, unbalanced loads or too much detergent foam can stop some machines spinning out the water, so remove a few items or run an extra rinse. On a semi-automatic machine, check that the drain selector knob is turned to Drain.

  2. Step 2: Check the drain hose

    Unplug the machine and pull it out gently. Follow the drain hose from the back to the drain and straighten any kinks or places where it is squashed against the wall. Whirlpool says the hose should go no more than 113 mm (4.5 in) into the standpipe and should not be taped in: it needs an air gap so water is not siphoned back. If your hose drains into a floor trap or a sink, make sure the end is not under water.

  3. Step 3: Clean the pump filter (front loaders)

    On most front-loading machines, the pump filter sits behind a small cover at the bottom front. Put towels and a shallow tray underneath. If there is a small drain tube next to the filter, use it to let the water out slowly first. Then unscrew the filter anticlockwise, remove coins, hairpins, lint and buttons, rinse it, and screw it back firmly so it does not leak. Top loaders often do not have a user-accessible filter: check your manual.

  4. Step 4: Check whether the home drain is blocked

    Take the end of the drain hose out of the drain and put it in a bucket held low. Run a spin-only cycle. If water pumps out strongly into the bucket, the washer is working and the blockage is in the standpipe, sink or floor drain: clear that instead. If little or no water comes out, the blockage or fault is inside the machine.

  5. Step 5: Check the machine is level

    A machine that rocks or sits at an angle can drain and spin poorly. Place a spirit level on top and adjust the feet until it sits firmly on all four. Samsung lists levelling as one of the checks for a washer that does not drain.

  6. Step 6: Run a test cycle

    Plug the machine back in, close the door and run a short rinse and spin with no clothes. Watch the drain hose and listen. If it drains now, clean the pump filter regularly (more often if you wash pet bedding or work clothes). If it still does not drain, or you hear a hum with no water moving, book a service visit.

Why a washing machine stops draining

The drain pump pushes water from the drum through the pump filter and drain hose into your home's drain. Anything that blocks that path stops the water: small items caught in the filter, a hose that is kinked, too long or pushed too far into the standpipe, or a household drain that is clogged with lint. A worn pump, a control fault or a door lock problem can also stop the cycle, and those need a technician.

Some machines will not drain while they detect too much foam or an unbalanced load. Using the right amount of a detergent made for your machine type (front loaders usually need low-suds, high-efficiency detergent) helps prevent that.

Front loader, top loader or semi-automatic?

  • Front loader: most have a pump filter at the bottom front that you can clean yourself.
  • Fully automatic top loader: often no user-accessible filter. Check the hose and drain, then call service.
  • Semi-automatic (common in India): the wash tub drains through the drain hose when the selector is set to Drain. Check the hose is lowered, not kinked and clear of lint.

Cold weather

In freezing weather, water left in the hose or pump can freeze. LG's advice is to pour warm (not boiling) water into the drum, wait 1–2 hours, then drain. Let the room warm up before running the machine again.

Parts and tools you may need

Most fixes in this guide need no parts, so do the checks first. If you do need one, match it to your brand and model before you buy.

As an Amazon Associate, AICK Studio earns from qualifying purchases. It does not change the price you pay.

Still full of water? When to call a technician

Call a qualified appliance technician if:

  • the pump hums or buzzes but no water moves after the filter and hose are clean,
  • the machine shows the same drain error after the checks above,
  • water leaks from underneath the machine,
  • the door stays locked with water inside and your manual's steps do not release it,
  • you smell burning or the MCB or breaker trips when the machine runs.

Do not open the machine's casing or replace the pump yourself unless you are trained.

Pump filter and foam questions

Why is my washing machine not draining?

The most common causes are a kinked or badly fitted drain hose, a clogged pump filter on front loaders and a blocked household drain. A failed drain pump is less common and needs service.

Where is the pump filter on a washing machine?

On most front loaders the pump filter is behind a small cover at the bottom front, often with a short emergency drain tube beside it. Many top loaders do not have one you can reach. Your manual shows the exact location.

How do I drain a washing machine full of water?

Unplug the machine and let hot water cool. On a front loader, use the emergency drain tube next to the pump filter to empty the water slowly into a tray, then remove the filter. You can also lower the end of the drain hose into a bucket on the floor to let water run out.

How often should I clean the washing machine pump filter?

How often to clean the pump filter depends on the model and how much you wash. LG suggests every 1–2 months in regular use, while some manufacturers give longer intervals. Follow your manual, and check the filter whenever water is slow to drain.

Can too much detergent stop a washer from draining?

Yes. Too much foam can stop some machines draining or spinning properly. Run an extra rinse with no detergent and use the dose your machine and detergent recommend.

Checked against: Whirlpool: Not draining (front load washer); LG US: Water not draining (OE error); LG UK: Why is my washing machine not draining?; Samsung: What to check if your washing machine doesn’t drain.

How TalkFixAI talks you through a fix

The screens below illustrate a TalkFixAI conversation that follows the steps in this guide. Your own conversation will depend on what you describe.

  1. Illustrated TalkFixAI chat. You: “My washing machine stopped with water still in the drum.” TalkFixAI: “First, unplug it. If it was a hot wash, let the water cool before you open anything.”
    Step 1Washer full of water?Drain it safely, step by step.
  2. Illustrated TalkFixAI chat. You: “It's unplugged and cool.” TalkFixAI: “Check the drain hose behind the machine for kinks.”
    Step 2Find the blockage.The hose first, then the pump filter.
  3. Illustrated TalkFixAI chat. You: “I can hear a hum, but no water comes out.” TalkFixAI: “If the filter and hose are clear, the pump may have failed. Book a service visit.”
    Step 3Know when it's the pump.A hum with no water moving.

Want TalkFixAI to talk you through this repair hands-free while your hands are busy? Try TalkFixAI, the free repair assistant that answers by voice, even offline.

Other appliance problems