A faucet that drips when closed almost always has a worn seal inside. In older two-handle taps that is a rubber washer; in quarter-turn and single-lever taps it is a ceramic cartridge or its O-rings. Shut off the water supply, take the handle off, and replace the worn part with an identical one.
Water off, handle off, seal out
Step 1: Shut off the water supply
Turn the isolation valve under the sink, or on the pipe to the tap, clockwise until it stops. If you cannot find one, close the main valve for the house or the overhead tank line.
Step 2: Drain the remaining water
Open the tap fully to let out the water left in the pipe. When it stops flowing, the supply is off. Plug the sink and lay a towel in it to catch small parts.
Step 3: Remove the handle
Prise off the decorative cap on top of the handle with a flathead screwdriver or butter knife to expose the screw. Undo the screw and lift the handle off. Some taps use a small hex (Allen) screw on the side instead.
Step 4: Take out the valve and inspect the seal
Use an adjustable spanner (wrench) to unscrew the valve body or cartridge anticlockwise. On a two-handle compression tap, look at the rubber washer at the bottom: if it is flattened, cracked or hard, it is the cause. On a quarter-turn or single-lever tap, look for worn O-rings or a chipped ceramic disc.
Step 5: Replace with an identical part
Take the old washer or cartridge to a hardware or plumbing shop to match the size exactly. Fit the new part, screw the valve back in firmly without overtightening, and refit the handle.
Step 6: Turn the water back on slowly and test
Open the supply valve slowly and check for leaks around the handle and the spout. Turn the tap on and off a few times. If it still drips, the valve seat may be worn, which needs a seat-reseating tool or a new tap.
Why fix a small drip?
A steady drip wastes a surprising amount of water. The US EPA's WaterSense program estimates that a faucet dripping once per second can waste more than 3,000 gallons (over 11,000 litres) a year. A drip can also leave mineral stains in the basin, and it tends to get worse as the seal wears further, so fixing it early is usually a small, cheap job.
Know which tap you have
- Two-handle compression tap: the handle turns several times from off to fully on. Usually fixed with a rubber washer.
- Quarter-turn tap: the handle turns only a quarter or half turn. Common in Indian bathrooms and kitchens. Usually fixed with a new ceramic cartridge or spindle.
- Single-lever mixer: one lever controls hot and cold. Usually fixed with a new cartridge from the tap's manufacturer.
If the tap is still under warranty, check the manufacturer's instructions or service line before taking it apart.
Parts and tools you may need
Most fixes in this guide need no parts, so do the checks first. If you do need one, match it to your brand and model before you buy.
- Faucet cartridgeTake the old one out first and match the brand and shape exactly.Find on Amazon: Faucet cartridge →
- Faucet washer and O-ring kitFor older taps that seal with a rubber washer.Find on Amazon: Faucet washer and O-ring kit →
- Plumber’s silicone greaseA thin coat on new O-rings helps them seal and last.Find on Amazon: Plumber’s silicone grease →
- Adjustable wrenchTo undo the retaining nut without rounding it.Find on Amazon: Adjustable wrench →
As an Amazon Associate, AICK Studio earns from qualifying purchases. It does not change the price you pay.
When to call a plumber instead
Call a plumber if:
- you cannot shut off the water supply,
- the valve body is corroded or seized and will not turn,
- water leaks from the wall or under the basin rather than the spout,
- the tap still drips after a new washer or cartridge,
- the tap is a wall-mounted mixer with concealed valves.
Leaky tap questions
Why does my tap keep dripping when it is turned off?
A worn rubber washer, worn O-rings or a damaged ceramic cartridge inside the tap is no longer sealing. Replacing that part usually stops the drip.
Can I fix a dripping tap without turning off the water?
No. Opening the valve with the supply on will spray water under pressure. Always close the isolation valve or main supply first.
How do I know what size washer or cartridge to buy?
Take the old part to a hardware or plumbing shop and match it exactly. For branded mixers, order the cartridge using the tap’s model number.
Is tightening the handle harder a good fix?
No. Overtightening crushes the washer or cracks a ceramic disc and makes the leak worse. Replace the worn part instead.
Checked against: US EPA WaterSense: Fix a Leak Week.
How TalkFixAI talks you through a fix
The screens below illustrate a TalkFixAI conversation that follows the steps in this guide. Your own conversation will depend on what you describe.

Step 1Tap dripping when it's off?Find the worn part, step by step. 
Step 2Hands busy? Just listen.Each step read out while you work. 
Step 3Know when to call a plumber.Stuck valves and corroded fittings.
Want TalkFixAI to talk you through this repair hands-free while your hands are busy? Try TalkFixAI, the free repair assistant that answers by voice, even offline.